Bienvenido, Invitado
Nombre de Usuario: Contraseña: Recordarme
  • Página:
  • 1
  • 2
  • 3

TEMA: A new job remodeling a Stug

A new job remodeling a Stug 4 años 1 mes antes #64205

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
Now I do have first gone on with the electrical system a bit since my printer is busy.

First loaded and checked the new battery if it's okay. A complaint after the conversion is not recognized.
When I use Battery 8 cells Nihm what has turned out for me as perfect.



The battery I cut gently in the middle to shrink the tubing and wrinkle it easy from.





The sheet metal connector I turn wary of Poland from causing a short circuit without and loop to the now exposed terminals.





ZumVerlöten I use a cheap soldering iron from the hardware store. It is important in this is that he has at least 80-100 watts of power to the battery to be able to solder quickly and so gentle.



Before I connect the battery again I still need two matching of the length of cable which I well tin solder at both ends. It should not save the tin man. I also binge tin on the poles of the batteries, but always make sure they do not pay attention anyway just to close.



So I solder now always positive and negative poles of the battery opposite. In order to prevent a short circuit because I glue one end of the cable first from yet.





About the free ends I stick then duct tape and so the battery can now take place in the tank.



The last few days is also the Beier sound module and the station arrived.





The transmitter I have spent today first time to the charger. The sound module I install ever with all the cabling piece by piece.





Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64209

  • pacomerlo
  • Avatar de pacomerlo
  • Fuera de línea
  • Teniente General
  • Teniente General
  • "Trompudo"en movimiento.DBHMSSE 1:16 reorganizado
  • Mensajes: 1541
  • Gracias recibidas: 113
Edwin Amigo, is that the sound card that can be used for my tank?

As usual a very good job, congratulations for him.


Saludos y suerte.

El departamento I+D+I Cerrado hasta nueva orden
EL DBHMSSE 1:6 organizado y preparado para lo que venga
Pantherturm/operativa. VLA/operativo. E-100/operativo. Köenigtiger/de baja temporal. Ferdinand/operativo.
El DBHMSSE 1:16 reorganizándose 1 Panzer III 1 Panzer IV 1 Jagdpanther 6 Tiger

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

El departamento I+D+I Cerrado hasta nueva orden
EL DBHMSSE 1:6 organizado y preparado para lo que venga
Pantherturm/operativa. VLA/operativo. E-100/operativo. Köenigtiger/de baja temporal. Ferdinand/operativo.
El DBHMSSE 1:16 reorganizándose 1 Panzer III 1 Panzer IV 1 Jagdpanther 6 Tiger

A new job remodeling a Stug 4 años 1 mes antes #64212

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
Hi Paco,

exactly this I meant. If you have a particularly tepid want'll Because even connect a downstream amplifier. Dasmachen with us a lot in your large models.



After the transmitter is now loaded I could him today programming and everything went as usual after a few small adjustments as it should.



The only little thing was a fuse. 20A is too little when you brake fully.



Now 30A are installed and that should hold.

Then the speaker was still in the series. First I glued the lid and made ​​the holes for the connecting cable. As damping insert a piece of filter for cooker hoods has proven to me.







Thus, the space in the tank is optimally utilized and also the upper tray fits perfectly on it.



El siguiente usuario dijo gracias: WITTMANN, pacomerlo

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64220

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
Once the lower hull with the associated technology is now almost ready today I have been interested in the programming of the sound module.



And of course, tried out in the wild.



The final details are still lacking, but I'm then using the technique of upper hull.

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64221

  • jcm
  • Avatar de jcm
  • Fuera de línea
  • Teniente
  • Teniente
  • ¡¡ hola ¡¡¡¡
  • Mensajes: 472
  • Gracias recibidas: 69
:woohoo: :woohoo: :woohoo: :woohoo: :woohoo: :woohoo:

Hello Edwin.
Great work with the stug.

What sound card you have?

I congratulate you!!!. a great job

regards

King tiger hl 1/16
Sherman M4 mato 1/16
Persing HL 1/16
caza carros M36 yakcson 1/16
Tiger I 1/24
auto construidos.
Puente beilys - 1/16
LCM 3 - 1/16
vehiculo asalto anfibio AAVV- A7 - 1/16
SHERMAN M4A3E8 - 1/16

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

King tiger hl 1/16
Sherman M4 mato 1/16
Persing HL 1/16
caza carros M36 yakcson 1/16
Tiger I 1/24
auto construidos.
Puente beilys - 1/16
LCM 3 - 1/16
vehiculo asalto anfibio AAVV- A7 - 1/16
SHERMAN M4A3E8 - 1/16

A new job remodeling a Stug 4 años 1 mes antes #64224

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
Hi jcm,

thank you for your opinion.

The sound module is Beier.

www.beier-electronic.de/modellbau/home/home.php

regards Edwin

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64236

  • Jussek
  • Avatar de Jussek
  • Fuera de línea
  • Moderador de 1ª Clase
  • Moderador de 1ª Clase
  • Mensajes: 1280
  • Gracias recibidas: 273
Edwin, your link goes to the Beier initial webpage

what card did you use, the USM-RC or USM-RC2?

best regards

OKW - Panzergruppe Tarraco

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

OKW - Panzergruppe Tarraco

A new job remodeling a Stug 4 años 1 mes antes #64237

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
Hi Jussec,

I only use the USM RC 2, since only this provides all the functions that I use.
The sound module with its functions very extensive, offers almost endless possibilities and the manufacturer's support is excellent with questions and problems. This is the reason why I use it.

regards Edwin
El siguiente usuario dijo gracias: pacomerlo

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64241

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
Currently I only had the time to construct a pivot for the carriage of Stugs.
However, the G-code for printing is also ready and maybe I can still make overnight.



There is now separated to Page Align the Stug the rocker and the pivot bearing can now be both, or just the rocker rebuild.

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64248

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
The hinge was this morning then printed.



But to install it I had to prepare a few things. In the upper part disturbed nor the old fortifications and the box and the gunner's hatch had to get away.







In order to mount the mount to the pivot, I have this but not glue it and attach the holes for the screws.
First, pre-drill the joint with a 2mm drill.



Then put the gun mount it and this pierce to the hinge as a template it with the 2mm drill.



Last drill out the mount from the top with a 3mm drill.



So you can then glue the joint base to the hull top, put through the gun carriage from the front and befesigen with a screw. So you get a stable, smooth-joint to Page Aim ​​the cannon.





Next, the canon rocker stuck in the inner part of the mount, with 2mm pre-drilling and screw.







For installation of the rocker, I now had to cut a little bit. So the rocker but can be re-installed as described in the expansion.

[img]http://up.picr.de/19036608cp.jpg /img] And so now looks like the scales in favor of the side Align. [img]http://up.picr.de/19036611tq.jpg



I have already placed the servos to end for today.

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64304

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
And again it is coming to a piece, none of completion.

Today I installed the three servos and also still the same program the Align to Page on the transmitter. So you can align with a knob at the side the gun now.



The Evolation and the RCC, I must still be programmed directly at Beier sound module, but before that I have the veritable camouflage headlight and the excess flash.
So I'm going to the Stug then can pass its owner in Derbach 23.

By the way I now also have the parts to Page Align optimized and started a few to print them for printing the canon and the rocker bearings somewhat.

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64313

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
As I wrote yesterday sat down today and wired first, the LED `s.





After I again occupied myself with the settings on the sound module now works all the way I imagine it.
The cannon can be nice and slow in all directions move, the recoil works, save flash, I have thrown this time about the Beier sound module and the LED let a little longer than a normal flash light (for firing a gun also arises not so short flash as a Fotoapperat), the camouflage headlight can be turned on and a sound is active MG. A terminal for an MG I have programmed, but not connected to the LED in the viewing slot. No Stug there had a gun.

Now I just have to lay the cables and adjust so that everything without driving each other to work of disabled.



Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64340

  • pacomerlo
  • Avatar de pacomerlo
  • Fuera de línea
  • Teniente General
  • Teniente General
  • "Trompudo"en movimiento.DBHMSSE 1:16 reorganizado
  • Mensajes: 1541
  • Gracias recibidas: 113
Edwin, beautifull. Greate job friend.


Saludos y suerte.

El departamento I+D+I Cerrado hasta nueva orden
EL DBHMSSE 1:6 organizado y preparado para lo que venga
Pantherturm/operativa. VLA/operativo. E-100/operativo. Köenigtiger/de baja temporal. Ferdinand/operativo.
El DBHMSSE 1:16 reorganizándose 1 Panzer III 1 Panzer IV 1 Jagdpanther 6 Tiger

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

El departamento I+D+I Cerrado hasta nueva orden
EL DBHMSSE 1:6 organizado y preparado para lo que venga
Pantherturm/operativa. VLA/operativo. E-100/operativo. Köenigtiger/de baja temporal. Ferdinand/operativo.
El DBHMSSE 1:16 reorganizándose 1 Panzer III 1 Panzer IV 1 Jagdpanther 6 Tiger

A new job remodeling a Stug 4 años 1 mes antes #64345

Hello,
You use one servo for move up and down the canon, but the servo return to center all the time really?

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

A new job remodeling a Stug 4 años 1 mes antes #64377

  • Edwin
  • Avatar de Edwin Autor del tema
  • Fuera de línea
  • Teniente
  • Teniente
  • Edwin
  • Mensajes: 355
  • Gracias recibidas: 27
I use the functions on the gun 3 servos.

The for lateral straightening is directly controlled via a rotary knob on the receiver.
The raising and lowering of the gun and the recoil is about two servos controlled that I control via the Sondmodul and their functions I can freely program.

Por favor, Identificarse o Crear cuenta para unirse a la conversación.

  • Página:
  • 1
  • 2
  • 3
Gracias a Foro Kunena
Joomla templates by a4joomla